Accurate real‐time hybrid earthquake simulations on large‐scale MDOF steel structure with nonlinear viscous dampers          下载免费PDF全文

Baiping Dong  Richard Sause  James M. Ricles 《地震工程与结构动力学》2015,44(12):2035-2055

This paper presents real‐time hybrid earthquake simulation (RTHS) on a large‐scale steel structure with nonlinear viscous dampers. The test structure includes a three‐story, single‐bay moment‐resisting frame (MRF), a three‐story, single‐bay frame with a nonlinear viscous damper and associated bracing in each story (called damped braced frame (DBF)), and gravity load system with associated seismic mass and gravity loads. To achieve the accurate RTHS results presented in this paper, several factors were considered comprehensively: (1) different arrangements of substructures for the RTHS; (2) dynamic characteristics of the test setup; (3) accurate integration of the equations of motion; (4) continuous movement of the servo‐controlled hydraulic actuators; (5) appropriate feedback signals to control the RTHS; and (6) adaptive compensation for potential control errors. Unlike most previous RTHS studies, where the actuator stroke was used as the feedback to control the RTHS, the present study uses the measured displacements of the experimental substructure as the feedback for the RTHS, to enable accurate displacements to be imposed on the experimental substructure. This improvement in approach was needed because of compliance and other dynamic characteristics of the test setup, which will be present in most large‐scale RTHS. RTHS with ground motions at the design basis earthquake and maximum considered earthquake levels were successfully performed, resulting in significant nonlinear response of the test structure, which makes accurate RTHS more challenging. Two phases of RTHS were conducted: in the first phase, the DBF is the experimental substructure, and in the second phase, the DBF together with the MRF is the experimental substructure. The results from the two phases of RTHS are presented and compared with numerical simulation results. An evaluation of the results shows that the RTHS approach used in this study provides a realistic and accurate simulation of the seismic response of a large‐scale structure with rate‐dependent energy dissipating devices. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

A distributed parameter model of a frame pin‐supported wall structure          下载免费PDF全文

Peng Pan  Shoujun Wu  Xin Nie 《地震工程与结构动力学》2015,44(10):1643-1659

Many reinforced‐concrete frames collapse via a soft‐story mechanism during severe earthquakes. Such collapses are mainly attributed to concentrated deformation in a soft story. Deformation control is thus important in preventing collapse. The frame pin‐supported wall structure is a type of rocking structure that releases constraints at the bottom of the wall. Previous research has obtained good results for the deformation control of this type of structure. However, the interior forces and strength demands of the pin‐supported wall have not been systematically explored. In this paper, a distributed parameter model is developed to investigate the strength demand of the wall in a frame pin‐supported wall structure. In the model, the pin‐supported wall is simplified as a bending beam and the frame is simplified as a shear beam. The two beams are joined by distributed shear connectors, so that the shear force can be transferred at any location on the interface. The model can be solved using differential equations based on equilibrium and compatibility. The accuracy of the model is verified using SAP2000 (Computers and Structures Inc., Berkeley, CA, USA). Displacement distribution of the structure and distributions of the moment and shear force within the pin‐supported wall are obtained for two typical external force profiles. It is found that the pin‐supported wall can effectively reduce the drift concentration factor. Distributions of the displacement, moment, and shear force are closely correlated with the relative stiffness of the wall and frame. Finally, recommendations on the stiffness and strength of a pin‐supported wall are made. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

用微振动勘探方法探测隐伏断裂构造   总被引：1，自引：0，他引：1       下载免费PDF全文

范小平  李细兵  赵启光  宋浩  戴波  张帅帅 《地震学报》2015,37(1):134-143

介绍了运用微振动勘探方法探测隐伏断裂构造的方法和思路,并对郯庐断裂带两条分支断裂进行了试验性勘探．通过与人工地震勘探结果对比分析,发现微振动勘探方法对隐伏断裂构造具有较好的空间定位能力,其对岩性差异面形成的断裂定位误差与人工地震勘探结果相当; 又因其具有较大的勘探深度,因而可以有效揭示勘探区域下方地层及断裂的空间分布特征及其接触关系,这对于识别和确定断裂构造的主破裂面具有重要意义. 但微振动勘探方法对地层或断裂构造细节特征的揭示能力较差．因此,在实际地层或断裂勘探中,宜采用人工地震勘探方法与微振动勘探方法相结合的方式确定断裂的深浅构造关系,可以用微振动勘探方法进行普查,在确定断裂初步位置及空间展布特征后,再选用人工地震勘探方法进行断裂精确定位．   相似文献   

2014年秭归M_S4.5和M_S4.9地震震源与发震构造特征     

WU Hai-bo  YAO Yun-sheng  SHEN Xue-lin  ZHAO Ling-yun 《地震地质》2015,37(3):719-730

2014年3月27日和30日湖北秭归县发生了三峡水库蓄水以来该地区最大的2次地震,文中通过多种方法分析了2次地震的震源与发震构造特征。采用Kiwi方法反演2次地震的矩张量解,该方法中使用了湖北和重庆测震台网14个宽频带波形记录和6层地壳速度结构模型,反演结果显示,2次地震观测谱和波形与理论谱和波形拟合得比较好,非拟合误差数0.57,表明反演结果是可靠的。2次地震均为走滑兼少量逆冲错动,但前一地震为左旋走滑,后一地震为右旋走滑,矩张量解中DC成分偏少而ISO成分多可能是库水对地下介质物性影响的反映。同时也使用三峡台网15个子台记录的波形资料,采用双差定位法重新精定位了从3月27日至4月27日时段内超过500次地震序列事件,结果显示余震序列分布方向为NNW向和NE向,但主要集中在NE向,并分别沿NNW和NE向作了深度剖面,剖面显示震源深度为4.5~10.0km,余震在深部呈现2个较明显的断面,与震源机制解NE向节面产状一致。野外现场宏观烈度调查指出,Ⅴ度极震区等震线为一椭圆,长轴NWW向,短轴NE向,结合野外现场考察结果和震源区地质构造背景,综合推断仙女山断裂北端的NE向破裂面为2次地震的发震断面,余震序列的NE和NNW向分布、剖面上发震层的形态和深度特征表明,这次地震活动受到了仙女山断裂和九畹溪断裂活动的控制与影响。  相似文献   

沂沭断裂带重力场及地壳结构特征   总被引：5，自引：2，他引：3  

WANG Xin  ZHANG Jing-fa  FU Ping-jie  GAO Min 《地震地质》2015,37(3):731-747

沂沭断裂带为郯庐断裂带山东段,新构造运动显著,是华北地区的强震活动带之一。文中收集了该地区的布格重力数据,利用小波多尺度分析方法对重力场进行有效分离,研究区域地壳结构特征及断裂空间展布,并应用Parker变密度模型对区域莫霍面进行反演分析,得到以下几点结论:1)重力区域场显示,沂沭断裂带形成了NNE走向的大型重力梯度带,分隔了鲁西、鲁东地块,成为区域内重要的地球物理分界线。2)重力局部场显示,中上地壳结构复杂,沂沭带内部呈现两堑一垒的重力异常格局,5条主干断裂形成线性梯度带分布于东、西地堑内,鲁西块体的多条NW向活动断裂交切于沂沭断裂带,多数断裂只交切于西地堑,而蒙山山前断裂和苍尼断裂横穿沂沭断裂带;下地壳结构相对简单,发生明显的褶曲构造,表现出大规模高、低密度异常相间排列的典型特征。3)区域莫霍面形态东高西低,沂沭断裂带形成了莫霍面陡变带,造成了东西分异格局,潍坊东—莒县—临沂一线出现莫霍面上隆区,具有强震发生的深部孕震环境。4)区域内地震多发于高、低重力异常转化带之间,特别是活动断裂对应的重力梯度条带之上,地震的发生与断裂活动有着密切的关系,沂沭断裂带地震活动性最强,且东地堑强于西地堑。  相似文献   

紫坪铺水库地区震源位置和速度结构的联合反演   总被引：1，自引：0，他引：1  

WANG Liang  ZHOU Long-quan  HUANG Jin-shui  JIAO Ming-ruo  LIANG Yi-jing  YANG Mu-ping 《地震地质》2015,37(3):748-764

利用紫坪铺水库7个库区地震台站和10个区域地震台站记录的2004年8月至2008年5月的地震震相观测报告,通过震源位置和速度结构联合反演的方法,采用Simulps14软件对紫坪铺水库地区进行了小震精定位及速度结构反演。通过计算得到了紫坪铺水库地区记录到的几乎所有地震的精定位结果,以及0km、3km、6km和10km几个层面上较好的P波速度和波速比分布情况。精定位结果显示,紫坪铺水库地区的地震活动主要集中在虹口、玉堂镇和水磨3个地区。层析成像和波速比结果则较好地反映了紫坪铺地区受到水库渗水的影响范围及紫坪铺水库对汶川地震的影响。整体上来讲,紫坪铺水库的西南端水库渗水作用最大深度≤8km,汶川主震深度上没有明显的P波低速异常,也没有明显的波速比高值异常,说明水的渗透作用并没有达到汶川主震位置深度,即水对汶川地震的发生没有直接作用。  相似文献   

Shaking-table tests and numerical simulations on a subway structure in soft soil     

《Soil Dynamics and Earthquake Engineering》2015

Shaking table tests were performed to investigate the damage mechanisms of a subway structure in soft soil while experiencing strong ground motions. The seismic responses of the structure and soil were found to be more sensitive to input motions with richer low-frequency components. The excess pore pressure ratio of soil increased slightly, and the distribution of the excess pore pressure surrounding the structure showed clear spatial effects. The frequency spectrum characteristics of input ground motions clearly influenced the lateral displacement of the structure. In addition, the structure was most severely damaged at the top or the bottom of the interior columns. Finite element analyses were conducted by using the modified Martin–Seed–Davidenkov viscoelastic and the rate-independent plastic-damage constitutive models for soil and concrete, respectively. Satisfactory agreement was observed between the simulation and test results, the difference between these results was discussed in detail. The results provide insight into how the characteristics of strong ground motion might influence and present a simplified analysis method to quantitatively evaluate the damage of subway structures in soft soil.  相似文献   

Pipe–soil interaction and pipeline performance under strike–slip fault movements     

《Soil Dynamics and Earthquake Engineering》2015

The performance of pipelines subjected to permanent strike–slip fault movement is investigated by combining detailed numerical simulations and closed-form solutions. First a closed-form solution for the force–displacement relationship of a buried pipeline subjected to tension is presented for pipelines of finite and infinite lengths. Subsequently the solution is used in the form of nonlinear springs at the two ends of the pipeline in a refined finite element model, allowing an efficient nonlinear analysis of the pipe–soil system at large strike–slip fault movements. The analysis accounts for large strains, inelastic material behavior of the pipeline and the surrounding soil, as well as contact and friction conditions on the soil–pipe interface. The numerical models consider infinite and finite length of the pipeline corresponding to various angles β between the pipeline axis and the normal to the fault plane. Using the proposed closed-form nonlinear force–displacement relationship for buried pipelines of finite and infinite length, axial strains are in excellent agreement with results obtained from detailed finite element models that employ beam elements and distributed springs along the pipeline length. Appropriate performance criteria of the steel pipeline are adopted and monitored throughout the analysis. It is shown that the end conditions of the pipeline have a significant influence on pipeline performance. For a strike–slip fault normal to the pipeline axis, local buckling occurs at relatively small fault displacements. As the angle between the fault normal and the pipeline axis increases, local buckling can be avoided due to longitudinal stretching, but the pipeline may fail due to excessive axial tensile strains or cross sectional flattening. Finally a simplified analytical model introduced elsewhere, is enhanced to account for end effects and illustrates the formation of local buckling for relative small values of crossing angle.  相似文献   

龙门山断裂带南段地壳一维P波速度结构   总被引：2，自引：0，他引：2  

王小娜  于湘伟  章文波  王思琳 《地震研究》2015,38(1)

基于2009年1月1日至2013年5月6日四川地震台网、重庆地震台网记录的龙门山断裂带南段587个地震的5 012个P波到时数据,利用最小一维速度模型方法反演了龙门山断裂带南段地壳一维P波速度模型及台站校正值,并将其应用到龙门山地区地震重定位中。结果表明,台站校正值表征出龙门山断裂带南段地表速度结构的横向不均匀性,青藏高原的彭灌杂岩体及宝兴杂岩体在近地表表现为高速异常,而四川盆地的第四纪沉积表现为低速异常。重定位后地震震源在北西向的剖面上呈明显的条带状并向北西倾斜,该地震带与宝兴杂岩下方的滑脱带延伸趋势一致。此外,该地震带上方分布着一条反冲地震带,两地震带呈"y"型分布,这可能是宝兴杂岩上方的岩层为调节逆冲过程受阻而产生的反冲运动所致。  相似文献   

2013年洱源M_S5.5地震序列M_L≥3.4地震的震源机制解研究     

杨军  苏有锦  李孝宾  叶泵  陈佳 《地震研究》2015,38(2):196-202,333

利用云南省地震台网的宽频带数据,采用CAP方法计算了2013年3月3日洱源MS5.5地震前后共10次ML≥3.4地震的震源机制解,分析了洱源MS5.5地震前后震源机制解的一致性变化特征,结合精定位结果、震后现场灾害评估报告及震区地质构造情况,判定维西—巍山断裂以西的苍山西麓炼铁盆地东缘主边界断裂带为洱源MS5.5地震的发震构造,震源机制解节面Ⅱ(走向160°、倾角48°、滑动解-99°)为其发震断层面。  相似文献